Once the last application is finished, it can be tempting to park the sprayer and move on to the next job. For growers using herbicide Canada has a short window between finishing fall applications and the arrival of freezing temperatures, so there’s one more job worth taking care of before the sprayer goes away: properly winterizing your sprayer.
If you’re still wrapping up fall applications, make sure your setup is right for the job, particularly when spraying fall-applied soil-active herbicides, with a product like Fierce EZ. The Nufarm article covers fall-specific considerations including residue management, water volume and spray quality.
Water left in pumps, valves, hoses, filters or boom sections can freeze and expand, potentially causing cracks, leaks and other damage. Product residue can also remain in the system over winter, while worn parts left unnoticed in fall can become problems when you’re trying to get spraying next spring.
A good sprayer winterization routine helps protect your equipment through the winter and gives you an opportunity to catch maintenance issues while there’s still time to deal with them. Southern Alberta equipment specialists, for example, recommend thoroughly flushing the system, draining lines, adding appropriate antifreeze and inspecting components before storage.
Why sprayer winterization matters in Canada
Draining the main tank doesn’t necessarily mean your sprayer is empty.
Water can remain trapped in pumps, filters, valves, boom sections and other low points in the plumbing. Once temperatures fall below freezing, even relatively small amounts of trapped water can become a problem.
Modern sprayers can make careful sprayer maintenance even more important. Larger booms, more plumbing and systems such as pulse-width modulation create additional components that need to be considered when cleaning and preparing a machine for winter.
A good winterization routine should accomplish three things: clean crop protection products out of the system, protect components from freeze damage and identify maintenance issues before the next spray season begins.
Start with a thorough sprayer cleanout
Before worrying about freezing temperatures, start with a clean machine.
Follow the sprayer manufacturer’s instructions and the cleanout directions for the crop protection products that were last used. Whether your last application involved a fall herbicide Canada growers commonly use or another crop protection product, make sure you follow the product-specific cleanout requirements. Rinse the tank and circulate the cleaning solution through the entire spray system, paying particular attention to boom lines, filters, screens and nozzles.
The ends of longer booms deserve some extra attention because spray mixture can remain there even after clean water has been pushed through the nozzles. Opening boom ends during the rinsing process can help remove trapped residue.
Cleaning a sprayer properly also gives you an opportunity to inspect components that may have gone unnoticed during the busy season. Look for worn hoses, leaking fittings, damaged nozzle bodies, plugged screens and anything else you’d rather repair now than discover during the first spray window next spring.
Get the water out
After cleaning, work through the sprayer methodically to remove as much water as possible.
Don’t stop at the main tank. Check boom plumbing, pumps, filters, valves, rinse systems and any accessory tanks or lines that could hold liquid. Depending on the sprayer and manufacturer’s recommendations, compressed air may also be appropriate for clearing water from parts of the system.
This is where being thorough matters. A small amount of water trapped in the wrong place can freeze, expand and damage a component that otherwise had plenty of life left in it.
Protect the system with sprayer antifreeze
Once the machine is clean and drained, an appropriate sprayer antifreeze or winterizer can be circulated through the system according to the sprayer and winterizer manufacturer’s directions.
The goal is to protect vulnerable components such as pumps, valves, seals and plumbing from the temperatures they’ll experience over winter. Products formulated specifically for agricultural sprayers are available for Canadian conditions, so check with your local ag retailer to learn more about these options.
The amount of winterizer and the process for circulating it will vary by machine, so stick with the sprayer manufacturer’s recommendations rather than relying on a one-size-fits-all procedure.
Use winterization as a maintenance opportunity
Winterizing farm equipment isn’t just about protecting it from freezing. It’s also an opportunity to get ahead of next year’s maintenance.
Inspect pumps, fittings, filters, hoses and seals while the machine is clean. Look closely at nozzles for wear or damage and make a list of anything that should be replaced before spraying starts again.
Fall is a much better time to find these problems than spring.
If indoor storage is available, it can also help protect the sprayer from snow, ice and repeated exposure to changing temperatures. Regardless of where it’s stored, follow the manufacturer’s recommendations for electronics, batteries and other components that may have their own winter storage requirements.
Make spring startup easier
The work you put into sprayer winterization in fall can save time when the weather turns next spring.
Before loading crop protection products, inspect the machine, reinstall anything removed for winter storage and run clean water through the system. Check for leaks and make sure the pump, boom sections and nozzles are operating properly.
Testing everything with water first gives you a chance to catch problems in the yard rather than discovering them after the weeds are already growing.
Protect your sprayer before winter
Your sprayer is one of the most important pieces of equipment on the farm and Canadian winters aren’t particularly forgiving when water gets left in the wrong place.
Taking time to winterize your sprayer means cleaning out product residue, removing trapped water, protecting the system against freezing and checking components for wear before the machine goes into storage.
Do it properly in the fall and you’ll be in a much better position when it’s time to spray again.